1/2/02
ALA550
11
In this test mode, this system can test the Zone 1 Wireless PIR or Door switch / Zone 2 Instant ground
trigger / Zone 3 Door trigger and the Zone 4 optional sensor sensitivity. The installer can save time to test
the optional sensor sensitivity and sensor without using the traditional arming/disarming procedures to test
the sensors.
Enter:
1. Turn the Ignition 'switch ‘ON/OFF’ 3 TIMES and stay in OFF position.
2. Push the Valet switch 8 times and hold it until four chirps with a long chirp is hearing then release the
valet switch. You are now in the Alarm feature ‘IV’ programming mode.
4-a. Test the Zone 2 Instant Ground Trigger & Zone 3 Door Trigger:
Press and release the transmitter
button once. [1] LED flash, [1] siren/horn chirp to indicate your
are in Zone 2 / instant ground trigger and Zone 3 / Door trigger test mode.
Trigger sensor Siren chirps
Zone 2 / Instant Ground trigger (H7/2 Blue wire) 2
Zone 3 / Door trigger (H7/3 Violet & H7/5 Green Wire) 3
4-b. Test the Zone 4 / Optional Sensor (Connected to H2 4 Pin Plug):
Press and release the transmitter
button again. [2] LED flash, [2] siren/horn chirps to indicate your
are in optional sensor (connected to H2 4 pin plug) test mode.
1. Activate the warn-away (first stage optional sensor), system will emit a short chirp.
2. Activate the full alarm (second stage optional sensor), system will emit a long chirp.
3. Continue to test the optional sensor until reach the proper sensitivity.
4-c. Test the Zone 1 / Wireless PIR or Door Switch:
Press and release the transmitter
button again. [3] LED flash, [3] siren/horn chirps to indicate your
are in optional wireless PIR or Door switch test mode.
Trigger sensor Siren chirps
Zone 1 / Optional wireless PIR or Door Switch 1
RETURN TO FACTORY DEFAULT SETTING:
1. Turn the ignition ON then OFF 3 TIMES and stay in OFF position.
2. Push the Valet switch 12 times and hold it until six chirp with a long chirp is hearing then release the
valet switch. You are now in the “Return To Factory Default Setting” programming mode.
3. Press the
+ button on the transmitter together for 6 seconds, there will be a confirmation six
chirps and 3 long chirps to confirm the system “Alarm Feature I & II & III & IV Programming all return to
factory default setting.
Exit: Turn the ignition switch “on” or leave it for 15 seconds. A 3 long chirps to confirm exit.
OPERATION MANUAL
A.
TRANSMITTER OPERATION:
Transmitter Button System Function Remark
Lock Doors & Arm System
-
Arm and Delete The Zone 4 / Shock Sensor Press twice within 3 seconds.
- -
Arm and Noiseless mode Press within 3 seconds.
Unlock Doors & Disarm System
(2-second)
Disarm & Channel 2 (Trunk) Timer Control Press and Hold for 2 seconds
-
Two Steps Door Unlock & Disarm System Press twice within 3 seconds.
+
Silent Arming / Disarming
Ignition in "off" position.
+ (2-second)
Activate Anti Car-Jacking
Ignition in 'on' position and
Press and Hold for two seconds
(2-second)
Channel 2 (Trunk) Timer Control Press and Hold for 2 seconds
-
Passive Arming By-pass While the system disarmed.
Button = Panic Function. (Factory Default Setting)
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Komentáře k této Příručce